Open Access is an initiative that aims to make scientific research freely available to all. To date our community has made over 100 million downloads. It’s based on principles of collaboration, unobstructed discovery, and, most importantly, scientific progression. As PhD students, we found it difficult to access the research we needed, so we decided to create a new Open Access publisher that levels the playing field for scientists across the world. How? By making research easy to access, and puts the academic needs of the researchers before the business interests of publishers.
We are a community of more than 103,000 authors and editors from 3,291 institutions spanning 160 countries, including Nobel Prize winners and some of the world’s most-cited researchers. Publishing on IntechOpen allows authors to earn citations and find new collaborators, meaning more people see your work not only from your own field of study, but from other related fields too.
To purchase hard copies of this book, please contact the representative in India:
CBS Publishers & Distributors Pvt. Ltd.
www.cbspd.com
|
customercare@cbspd.com
Most often, in MST radar system, a few number of transmitters are non-operational due to various factors, making the liner sub-arrays corresponding to these transmitters in effective. This results in the thinning of the aperture and deviation of the excitation from the specified Taylor distribution. The array pattern will be distorted due to this deviation, when compared to the reference pattern. This chapter gives a complete analysis to quantify the distortion in the radiation pattern due to Aperture thinning. MATLAB was extensively used to analyze the results. The results of the radiation pattern in both principal planed and for different azimuth angles with and without thinning/tilt are presented. Radiation pattern is viewed in both polar and rectangular (2-D and 3-D) forms. Conclusions on the results obtained are presented.
Vignan Institute of Technology and Science, Affiliated to JNTUH, Hyderabad, India
*Address all correspondence to: nalidinesh@gmail.com
1. Introduction
The ever-increasing demand for the software development of Aperture thinned Radiation Pattern has motivated to model the present work. The Indian MST radar is a phased antenna array, highly sensitive operating at 53 MHZ with a peak power aperture product of 2.5 × 1010 W-m2. One for each polarization, it consists of two collocated orthogonal sets of 1024 3-element Yagi-Uda antennas. They are arranged over an area of 130 m × 130 m in a 32 × 32 matrix (Figure 1). The complete array setup is illuminated using 32 distributed transmitters of varying power. In turn distributed transmitters each will feed a linear sub-array of 32 antennas with a 32 parallel runs of center-fed-series-feed structures [1].
Figure 1.
Geometry for MST radar system.
Yagi-uda antenna is chosen for MST radar antenna array. Choice of an element for MST radar, advantages in favor Yagi element, requirements of side lobe level (SLL), antenna element design and modified Taylor distribution are explained [1, 2, 3, 4]. Amplitude distribution, illumination efficiency and feeder efficiency are derived. Finally MST radar specifications are tabulated.
While planning for the antenna element designing, the sharing antenna elements architecture of fixed overlap sub array to avoid grating lobe in the antenna pattern technique is also considered [5].
An experiment made to generate low side lobe patterns optimizing ring radii and individual element excitations from concentric circular arrays [6] does not worked for MST radar array. The approach of array excitation weight vectors as imaginary number chromosomes are often used as a general tool for pattern synthesis of absolute arrays that uses decimal linear crossover [7]. WWII elevated the phased-array antennas and has become a perfect tool for RF systems [8]. Then the main focus on the G-band multifunction measuring instrument systems for the Land is developed [9]. A coupled structural-electromagnetic model of phased array antenna PAA is developed to explain the performances of antenna, and the result of random errors and mechanical distortion [10]. Random error is generated throughout the producing and assembly method, and mechanical distortion is caused by external masses like high thermal distinction, vibration and impact loads [11]. Arrays produce aperture errors [12] as their determination is sometimes neglected, being in several cases very troublesome, such errors area unit mutual effects between parts of AN array, scattering from and obstruction because of the feed of a parabolic reflector, and optical phenomenon at a lens antenna step etc. [13].
Indian MST Radar antenna array uses a two-dimensional filled antenna array for both transmission and reception. An inter-element spacing of 0.7λ (λ, being the radar wavelength) is used in both the principle directions, which allows a grating lobe free beam scanning up to an angle of about 240 from broadside direction [1].
2.1 Choice of the element
To obtain the gain of 36 dB as given in the MST radar specifications a filled aperture of roughly 21λ to 25λ is required. To fill this aperture the number of elements required are given as
N=Total Aperture AreaApEffective Area of Single ElementAeE1
Where Ae = λ2Ge/4π.
Table 1 gives the total number of elements required to fill up the aperture for different types of antenna elements. Comparative study of the various antennas as the potential elements in MST radar configuration was made the possibility of using following types. They are Crossed Dipole over a ground plane, Coaxial Collinear, Three –element Yagi, and Four-element Yagi.
S.No
Types of Elements
Effective Gain Ge
Effective Area Ae
No. of elements N
Approximate grid spacing
1
Isotropic
1
λ2 / 12
63
0.29
2
Dipole
1.5
λ2 / 8
42
.35
3
Dipole over ground Plane
3
λ2 / 4
21
0.5
4
Yagi 3 element
5
λ2 / 2.5
12
0.64
5
Yagi 4 element
8
λ2 / 1.5
79
0.83
Table 1.
Different types of elements, and their number required to fill the aperture.
Out of these elements, the crossed dipole over a ground plane has the gain of the order of 5 dB and hence total number of dipoles required to fill the same aperture is quite large compared to the Yagi types and would require a more complicated and expensive feed network. The Coaxial Collinear (CoCo) antenna, which again is another form of dipole over a ground plane, is apparently simple to fabricate. These can be directly constructed at the site using RG 8/U or equivalent RF cables, but maintenance and water proofing of such an array would be tough.
A Yagi-Uda array consists of many parallel dipoles with different lengths and spacing, out of which only one is actively fed and others are shorted at their feed points. Since only one of the dipoles is driven and all other elements are parasitic, the later functions respectively as a reflector or as a director. In general, the longest shorted element with length of the order of λ/2 is the reflector and the shorted element is the director. This can be viewed as the array of dipoles in which all but the driven elements (Exciters) are short-circuited. For three-element Yagi case Voltage is
Vm=∑n=13InZmnE2
Where, In is the current on the nth element
m is the element number
Putting V1 = V2 = 0 and simultaneously solving these equations gives
I1I2=Z13Z32−Z12Z33EE3
I3I2=Z13Z12−Z23Z11EE4
Where, E = Z11Z33– Z31Z13.
Using these current rations, the input impedance, gain and radiation pattern can be calculated.
2.2 Antenna element design consideration
The single element gain and radiation pattern change considerably in the array environment. The physical area that each element couples limits the element gain in an infinite array [2, 3, 14] and is given by
gr=4πdxdy/λ2cosθE5
for, dx = dy = 0.7λ
gr=4π0.49=6.157=7.89dBE6
A practical element with a gain higher that this value, would lead to overlap of effective areas, without any useful addition to the array gain. The three-element Yagi appears to be a practical choice as the element of the MST array. It has a higher front-to-back ratio, which is useful in minimizing the ground effects and it can be designed to have a gain between 6.5 dB to 8 dB.
Considering the isolated Yagi element gain as 7.2 dB, the total array gain at a taper frequency of 80% works out to be 36.3 dB. This would leave a margin of 0.3 dB towards gain loss due to amplitude and phase errors across the aperture, thus allowing us to realize a gain of 36 dB for the zenith beam. The diameter of the element was chosen to be 0.75 inch, which is a standard commercially available tube.
The following values were found to offer satisfactory performance
L1: Length of the reflector
=2.799 m.
L2: Length of the exciter
=2.677 m.
L3: Length of the director
=2.369 m.
D1: Distance between reflector and exciter
=1.245 m.
D2: Distance between director and exciter
=0.895 m.
The expected performance of thee-element Yagi with the above parameters is tabulated below
Gain
7.236
Input Impedance
52.75 - j14.3
Front-to-back ratio
15 dB
2.3 Feeder network configuration
The feeder network of MST radar antenna array consists of two orthogonal sets; one for each polarization. The feeder network consists of thirty-two parallel runs of center-fed-series-feed (CFSF) structure. Thirty-two transmitters of varying power illuminate the array; each is feeding a linear sub-array of thirty-two antenna elements.
The feeder networks of all the sub-arrays are identical as far as the power distribution is concerned. The CFSF network, (shown in Figure 2) consisting of power divider at the center and a series of directional couplers on each side of its, connects the linear sub-array to the T/R switch, which delivers the transmitter output power to the array and the power received by the array to the corresponding low noise amplifier. Components of the feeder network are RG 1–5/8″, RS 7/8″ and air dielectric coaxial lines, Wilkinson type in-phase power divider, Distributed version of coupled line type directional couplers and Lumped version of hybrid type directional couplers [1].
Figure 2.
Center –fed-series-feed (CFSF) network.
Description of each of the above components is given below.
2.4 Rigid cable
RG 1–5/8″ cable is used to carry the output power of high power transmitters (70 kW – 120 kW range) to the CFSF network. RG 7/8″ is used to carry the output power of low power transmitters (15 kW – 53 kW range) to the sub-array input. This cables use foam dielectric, which is having a velocity factor of 0.89 at 53 MHz, the operating frequency, these cables offer an attenuation of about 0.5 dB per 100 m.
2.5 Power divider/combiner
This device acts as a divider in the transmit mode and as a combiner in the receive mode. The circuit diagram of Wilkinson type divider/combiner is shown in Figure 3. All the three ports are terminated with characteristic impedance, Zo (50 Ω). Ports 2 and 3 are isolated. During the transmit mode the transmitter output power is fed to the port-1, which will be divided in phase equally between the output ports 2 and 3. In the receive mode the power received by the two halves of the linear sub-array will be delivered through series feed network to the ports 2 and 3 respectively which will be combined in phase art port-1.
Figure 3.
Wilkinson type divider/combiner.
The relationship between the voltages in the transmit mode at the output and input ports is given by
V2=V3=−jV1/V2E7
The relationship between the voltages in the receive mode at the output and input ports is given by
V1=−jV2/V3/√2E8
Where, Vi is the voltage at the port-I. Since the two halves are symmetry V2 = V3 = V.
Therefore.
V1=−j√2VE9
2.6 Distributed versions of coupled line directional coupler (DC)
The coupled rod co-axial directional coupler is shown in Figure 4. In the Figure 4, section, 1–2 is the main line and 3–4 is the auxiliary line, which is coupled to the main line. As the electric current passes through Section 1–2 from port-1, it produces a magnetic field around it. This magnetic field couples with conductor 3–4 and induces current in it. Therefore, by varying the separation between the two conductors, we can control the coupling factor.
Figure 4.
Coupled line directional coupler.
In the transmit mode port-1 is the input port to which the power will be fed. Port-2 is the direct output power and portr-3 is the coupled port through which antenna will be energized. Port-4 is isolated with respect to port-1. The relationship between various voltages is given by
V3=kV1V2=−j√1−K2×V1V4=0×V1=0E10
Where Vi is the Voltage at port-i. This indicates that V1 and V3 are in phase and V2 is lagging V3 by 900.
All the thirty-two antennas within a sub-array should get the excitation signals with same phase so as to produce a main beam in the broad side direction resulting in high gain. In order to achieve this, the lengths of the feeding cables (running from the coupled port to the antenna balun) are adjusted accordingly. This process is called Phase equalization.
In the receive mode the antenna delivers power to the coupled port (port-3) and port-2 will be fed by the power coming from the adjacent coupler. In this mode, as a consequence of the phase equalization, V2 always leads V3 by 900. The relationship between the various voltages is given by
V1=√1−K2V2+kV3E10a
V4=√1−k2V3−kV2E11
2.7 900 Hybrid coupler lumped version
This coupler comprises of four quarter-wave sections, two in series and two in shunt. Each quarter line is realized by equivalent π section of lumped elements (inductors and capacitors) [2, 3].
In this structure, diagonally opposite ports are coupled. Since the coupled signal travels a distance of two quarter-wavelengths, it will be out of phase with respect to the input port. Powers given at the port-1 will be distributed between the direct output port-2 and coupled port-3. Port-4 is isolated. The coupling factor is dependent on the normalized impedance of series and shunt arm quarter-wave line sections, Zb and Za respectively. Coupling factor is given by.
k=−Zb/ZaE12
Condition for impedance matching is given by.
1/Zb2–1/Za2=1E13
2.8 Excitation coefficients in the transmit mode
The normalized amplitudes (Cn) for all antenna elements with respect to the first antenna from the divider is given by
Cn=Vkn∏i=1n−11−ki2E14
Where KI is the coupling factor of coupler ‘I’ from the center (divider).
2.9 Excitation coefficients in the receive mode
The normalized amplitudes (Cn) for all antenna elements with respect to the first antenna from the divider is given by
Cn=kn∏i=1n−11−ki2E15
Where KI is the coupling factor of coupler ‘I’ from the center (divider).
2.10 Illumination efficiency
Since the weighing factors of the antenna elements are same for both transmit and receive modes, illumination efficiency will be same for both the modes. Illumination efficiency is defined as “the ratio of effective length of the sub-array to the physical length”, which can be expressed as
ηill=116C1∑n=116CnE16
which is found to be 79%.
Feeder network consists of fifteen couplers on either side of the divider/combiner to feed 16 antennas on either side. The coupler rating in decibels and the corresponding coupling factors of all the fifteen couplers are given in Table 2. The corresponding coupling coefficients (Cn) are given in Table 3.
Coupler No. (N)
Coupler Rating In db
Coupling Factor Value(Kn)
1,2
10
0.316
3,4
9
0.355
5,6,7
8
0.398
8,9
7
0.448
10,11
6
0.501
12,13
5
0.562
14
4
0.631
15
3
0.709
Table 2.
The coupler ratings and their corresponding coupling factor.
Sub Array (N)
Coupling Coefficients(Cn)
Sub Array (N)
Coupling Coefficients (Cn)
1
1.0000
9
0.7699
2
0.9488
10
0.7697
3
1.0112
11
0.6610
4
0.9454
12
0.6467
5
0.9908
13
0.5349
6
0.9090
14
0.4968
7
0.8339
15
0.4330
8
0.8611
16
0.4330
Table 3.
The coupling coefficients of the coupler.
2.11 Feeder network efficiency
Feeder network efficiency is defined as “the ratio of power delivered to the sub-array by the feeder network to the power output of the transmitter, feeding the sub array’. I the receive mode it is defined as “the ratio of the power delivered to LNA by the feeder network to the total power developed at the terminals of all thirty-two antenna elements during reception”. All feeder line components are assumed to the lossless in the computation of the feeder network efficiency. Normalized characteristic impedance of the system is assumed as unity in power calculations.
2.12 Transmit mode
When an input voltage of √2 volts is applied to the power divider, the voltage amplitude at the input of the first coupler will be one volt. The total power delivered to the sub-array is given by
Pout=2∑i=116An2unitsE17
Where An is the input voltage fed from the coupled ports of the directional couplers. Power input to the feeder network is,
PT=2volts2=2units
Feeder efficiency ηft is given by is found to be 100%
ηft=PantPrE18
2.13 Receive mode
In the receive mode, all the antennas of the sub-array equal powers and deliver the same to the coupled ports of the feeder network. When an input voltage of 1 volt is applied to all the coupled ports, the input power to the feeder network is given by
Pant=32×12=32watts.
The output voltage of the combiner (which is fed to the LNA) is:
Vout=√2V0,1E19
Where, V0,1 is the output of the first coupler. The combiner output power is given by.
Pout=2│V0,1│2E20
Feeder network efficiency is given by
ηfr=PoutPtnE21
and found to be 92.8%. Note that the rest of the power will be dissipated in the isolated ports of the directional couplers.
In addition to this, there will be a combining loss (at IF level) of 0.6 dB, which is equivalent to an efficiency of 92.3%, and due to amplitude imbalance there will be some loss that should be accounted in the overall feeder line efficiency. Hence, the total feeder efficiency of the MST radar planar phased array is equal to 85.6%.The specifications of MST radar are listed here:
Type of the array
Phased antenna array
No of elements
1024
Grid
Square
Configuration
32 × 32 matrix
Inter-element spacing
0.7 wavelengths
Physical aperture
130 m × 130 m
Aperture distribution
Stepped modified Taylor across the principal planes
Effective aperture
100 m × 100 m
Peak power aperture product
2.5 × 1010 W-m2
Gain
36 dB
Beam width
3o in the principal planes
Side lobe level
−20 dB
Beam steering
0 to 200 (in steps of 1o) from Zenith towards all directions
Most often, a few number of transmitters are non-operational due to various factors, making the linear sub-arrays corresponding to these transmitters ineffective. Even if the transmitters are operational, with in a sub-array, it is possible that some elements will not get the excitation signal due to weak connection or discontinuity problems in the feeder line. This results in the thinning of the aperture and the deviation of the excitation from the specified Taylor distribution. Due to this deviation, the array pattern will be distorted from the normal pattern. In this chapter, a detailed analysis is carried out to quantify the degradation in the radiation pattern due to aperture thinning. Phase-errors are assumed to the zero throughout.
3.1 Array pattern of 2 N MST radar
If the array aperture is in the x y-plane and sub-arrays are aligned parallel to y-axis with a spacing dx, along the x-axis, array pattern can be expressed as
fθϕ=∑m=12Nx∑n=12NyImne−jkSinθmdxCosϕ+ndySinθE22
Where dx = sub-array spacing along the x-axis
dy = element spacing within a sub-array (along the y-axis)
m = sub-array number along the x-axis
n = element number along the y-axis within a sub-array
θ = Field point angle from broadside
Ø = Azimuth angle
Imn = excitation current coefficient of nth element in mth row (sub-array)
2Nx = number of sub-arrays in x-axis
2Ny = Number of elements within a sub-array (along y-axis)
k = Phase constant (in free space)
For MST radar antenna array dx = dy = d = 0.7λ and 2Nx = 2Ny = 2 N = 32. If each row has the same current distribution, even though the current levels are different in different rows, that is
ImnIml=IInI11E23
Which is true for MST array case, and hence possible to separate the current distribution and the array factor can be expressed in the form
fθ∅=fxθØfyθ∅E24
In which
fxθϕ=∑m=12NIme−jmkdxSinθCosϕE25
fyθϕ=∑n=12NInejnkdySinθSinϕE26
and
Im=Im1I11E27
In=I1nI11E28
are the normalized current distributions in a row of elements parallel to x-axis and y-axis respectively. All the thirty-two elements are phase-equalized within a sub-array by adjusting the input feed cable lengths. Hence a linear sub-array, when excited alone, will produce a fan beam in the broadside direction. Beam tilting is done in E-plane (or Ø = 0o plane or xz-plane in this case) by providing progressive phase shift along the successive linear sub-arrays. The equations are executed in MATLAB to find the array patterns at different zenith angles.
If an array aperture is not fully excited, then it is said to be “Thinned”. When this thinning is applied for the MST radar array, which is a planar array with separable current distribution, the array pattern can be expressed as
where Im is proportional to the square root of output power of transmitters and in is proportional to the coupling coefficients of CFSF network. The array factors in both the principle planes, Ø 0o (E-plane) and Ø = 900 (H-plane), respectively are
fEθ=fθ0=∑n=12NIn∑m=12NIme−jmkdxSinθE30
fHθ=fθ900=∑m=12NIm∑n=12NIne−jnkdySinθE31
When some of the currents Im are zero (which means the corresponding transmitters are off), it is clear that the shape of H-plane pattern, fH(θ), will not be affected though its magnitude changes according to the first term in (31). However, the E-plane pattern, fE(θ), will be distorted according to the second term of (30). So, when few transmitters are non-operational only the e-plane pattern will be distorted. To study the effect of aperture thinning on the radiation pattern, it is required to compute in MATLAB the array pattern by letting some of the Im to zero, which is equivalent to putting the corresponding transmitters off.
The antennas in the sub-arrays would not get excitation signal, if few transmitters are non-operational. Though they are physical present, electrically they are not effective. If an array aperture is not fully excited, then it is said to be ‘thinned’. This results in the deviation of the excitation from the specified Taylor distribution. Due to this deviation, they array pattern will be distorted. To quantify the distortion in the radiation patterns in both E and H planes, the array pattern expressions are made to depend on the shape of the beam. Forcing some of the Im to zero, which means these transmitters are non-operational, can effect array thinning. Iy is clear that the shape of H-plane pattern, fH(θ), will not be affected, though its magnitude changes according to the first term in Eq. (31). However, the E-plane pattern, fE(θ), will be distorted according to the second term of Eq. (30) Hench, we can conclude that only E-plane pattern will be distorted and needs to the examined in case few transmitters are non-operational. Programming in MATLAB helped a lot to examine these cases.
Array pattern is computed in the E-plane with different thinning configurations, that is by letting group of transmitters (or sub-arrays) in effective. Radiation parameters are distorted for all the cases. The two important parameters that may affect the radar performance are gain and SLL. The variation of these two parameters with different array thinning configuration is tabulated in Table 4. Array pattern thinning obtained with and without tilting can be viewed from plot shown in the Figures 5 and 6.
S.NO
Sub-arrays or TXs OFF
Loss in the gain (dB)
SLL (dB)
1
Nil
0.00
−19.9
2
3,4
0.40
−19.9
3
5,6
0.50
−22.0
4
3,4,5,6
1.00
−19.5
5
5,6,27,28
0.55
−17.5
6
1 to 8
2.00
−16.0
7
1 to 8 and 25 to 32
4.00
−13.5
8
9,10
0.50
−18.3
9
11,12
0.80
−17.7
10
13,14
0.80
−15.2
11
15,16
0.80
−14.2
12
13,14,15,16
1.90
−11.5
13
15,16,17,18,19
2.00
−09.0
14
9 to 6
3.30
−07.0
15
6,8,9,17,24,29,30,32
2.50
−14.5
Table 4.
Variation of parameters with different array thinning configurations.
Figure 5.
Array pattern for the two principal planes.
Figure 6.
Array pattern for a tilt of 10 degrees in E-plane.
Array pattern is computed for different azimuth angles using Eq. (30) by letting all transmitters (or sub-arrays) effective. The important parameters that may affect the radar performance are gain and SLL. The variation of the SLL parameter is tabulated in Table 5. Array pattern computed for different azimuth angles obtained without thinning and tilting can be viewed from Figures 7–9.
S.No.
Azimuth angle (Ø)
SLL (dB)
1
0
−19.9
2
15
−21.5
3
30
−30.5
4
45
−39.5
5
60
−30.5
6
75
−21.5
7
90
−19.9
Table 5.
Variation of SLL standard configuration with different azimuth angles.
Figure 7.
H –plane pattern – without distortion and with a tilt of 10 deg.
Figure 8.
E plane pattern distortion due to array thinning transmitters off: 1 to 8 & 25–32 and tilt: 0 deg.
Figure 9.
E- plane pattern distortion due to array thinning transmitters off: 6, 8, 9, 17, 24, 29, 30 & 32 and tilt: 0 deg.
The antenna array 3-D array pattern obtained using MATLAB is shown in the Figure 10. Amplitude distribution is plotted using the Eq. (22). Figure 11 shows a 3–D plot of antenna array when fully excited. Distortions of amplitude distribution due to array thinning are shown in Figures 12 and 13.
Figure 10.
3-D Array pattern.
Figure 11.
3-D power distribution for MST radar antenna array.
Figure 12.
3-D power distribution for MST radar antenna array transmitters off: 1–8, & 25–32.
Figure 13.
Transmitters off: 6, 8, 9, 17, 24, 29, 30 & 32.
Polar plots plotted in MATLAB for both the principal planes are shown in the Figures 14 and 15. Radiation pattern for different azimuth angles obtained in MATLAB are shown in Figures 16 and 17.
Figure 14.
Radiation power pattern for both principal planes.
Figure 15.
Radiation power pattern for E-plane.
Figure 16.
Radiation power pattern for an azimuth angle of 150.
Figure 17.
Radiation power pattern for an azimuth angle of 300.
4.1 MATLAB package
The entire software is developed using the MATLAB package. MATLAB was chosen for the numeric computation and visualization of the array pattern. Matalb is a helpful tool to develop portable and graphical user interface software. After entering into the package, the menu options as shown in Figure 18 will be visible. The new file with the rated powers of the transmitters, and standard parameters of the MST radar can be selected and will have. dat extension. Figure 19 shows the window of the open file with open options such as m files, mat files etc.
Figure 18.
Array factor distortion analysis menu options.
Figure 19.
Array factor distortion analysis file open selection option.
The display window will be of the format shown in Figure 20. The format of the display window is of 6 x 8 matrix. Press <O.K > button to clear the display. The sub menu allows the user to view as well as enter the values of your choice for both transmitters and parameters values, for the further processing. Format for entering the values in 6 x 8 matrix is shown in Figure 21. The accept button is pressed for processing the entered values.
Figure 20.
Transmitter power ON/OFF status.
Figure 21.
Format for entering transmitter power values.
The Config option allows the user with two sub menu options 1) Tx-power and 2) Parameters. The TX-Power option allows the user to change the transmitter power levels with the help of the slider as shown in Figure 22. The TX-Power have 4 sub menu options for each hut that is NH-1, NH-2, SH-1, and SH-2. The user can change the parameters of the antenna array as shown in Figure 23, where the operational frequency in MHz, inter-element distance in wavelengths, number of rows and columns, tilt angle of the beam in degrees can be varied.
Figure 22.
The transmitter power levels changes in north hut 1(NH 1).
From the results obtained in MATLAB, it may be noticed that degradation in gain and SLL due to the absence of a few low power transmitters (Table 4) (1–4 cases) is not significant. Surprisingly, SLL improves with some low power transmitters off (case-3), where the loss in directive gain is only marginal symmetrical thinning gives higher SLL than asymmetrical thinning (cases 4 & 5). If all low power transmitters are off (case-7), then the array is similar to standard radar array (almost uniform distribution) giving a SLL of −13.5 dB.
On the contrary, the absence of high power transmitters causes SLL to increase significantly. From cases 8–11 of the table, it is clear that absence of even two transmitters increases the SLL by 1.5–6 dB. It may be noted that SLL depends on the position of transmitters that are off. Absence of central sub-arrays results in higher SLL. Cases 12–14 demonstrates that absence of more than four power transmitters give unacceptable SLL (worse than Uniform distribution case). Finally, case 15 represents the real time status of the radar on a particular operational day, where eight transmitters were not functioning.
For different azimuth angles, Radiation power pattern of the MST radar antenna array is plotted. Table 5 shows the radiation power pattern for different azimuth angles. and the variations of SLL for standard configuration of radar array, with different azimuth values. It is observed that the change in the SLL for different azimuth angles varies a lot compared to that of the SLL of the two principal planes. The main focus is on the analysis of distortion of array pattern due to thinning.
The following facts can be concluded from the pattern obtained using MATLAB:
The first SLL rises by 0.4 dB.
For a continuous distribution SLL taper off very fast. Far off, side lobe levels do not taper off fast.
Around 45c the side lobe level rises roughly by 10 dB
I deem it as privilege to acknowledge my indebtedness to all those people who have helped me in completing the investigation of the. I express my sense of gratitude and thanks to my guides Dr. P Srinivasulu, Engineer ‘SG’, NMST Radar Facility, Gadanki and Dr. N C Eswar Reddy, Professor, Sri Venkateswara University, Tirupathi for their valuable guidance, encouragement, inspiration and cooperation throughout the investigation.
References
1.MST Radar manual, “Characterization of MST Radar Antenna Array”, P. Srinivasulu, Scientist-F
2.Ricolindo L. Carino and Mark.F. Horstemeyer (July 7th 2016). Case Studies in Using MATLAB to Build Model Calibration Tools for Multiscale Modeling, Applications from Engineering with MATLAB Concepts, Jan Valdman, IntechOpen, DOI: 10.5772/62348
3.Bahadır Ergün and Cumhur Şahin (January 6th 2021). Laser Point Cloud Segmentation in MATLAB [Online First], IntechOpen, DOI: 10.5772/intechopen.95249
4.Constantine A. Balanis, “Antenna Theory analysis and Design”, (2nd edition). John Wiley & sons Inc. New York, 2005
5.Edward C. Jordon and Keith G. Balman, “Electromagnetic Waves and Radiating Systems”, (2nd edition), Prentice Hall of Indian Pvt. Ltd., New Delhi, 1991
7.H. Steyskal, “Simple method for pattern nulling by phase perturbation”, IEEE Transaction on Antennas and Propagation, vol.31, pp.163-166, 1983. 10.1109/TAP.1983.1142994
8.V.Rajya Lakshmi and G.S.N.Raju, “Optimization of radiation patterns of array antennas”, PIERS Proceedings, Suzhou, China, pp.1434-1438, 12-16 September 2011
9.Keen-Keong Yan and Yilong Lu, “Sidelobe reduction in array-pattern synthesis using genetic algorithm”, IEEE Transactions on Antennas and Propagation, vol.45, no.7, July 1997. 10.1109/8.596902
10.Haupt, R. L. and Y. Rahmat-Samii, “Antenna array developments: A perspective on the past, present and future,” IEEE Antennas and Propagation Magazine, Vol. 57, No. 1, 86–96, 2015. doi:10.1109/MAP.2015.2397154
11.Farina, A. and L. Timmoneri, “Phased array systems for air, land and naval defence applications in Selex ES,” 8th European Conference on Antennas and Propagation (EuCAP), 560–564, Hague, 2014. doi:10.1109/EuCAP.2014.6901818
12.Ruze, J., “The effect of aperture errors on the antenna radiation pattern,” Nuovo Cimento Suppl, Vol. 9, No. 3, 364–380, 1952. 10.1007/BF02903409
13.Wang, C., M. Kang, W. Wang, B. Duan, L. Lin, and L. Ping, “On the performance of array antennas with mechanical distortion errors considering element numbers,” International Journal of Electronics, Vol. 104, No. 3, 462–484, 2017. doi:10.1080/00207217.2016.1218064
14.Wang, C., et al., “Electromechanical coupling based performance evaluation of distorted phased array antennas with random position errors,” International Journal of Applied Electromagnetics and Mechanics, Vol. 51, No. 3, 285-295, 2016. doi:10.3233/JAE-150170
15.Hsiao, J. K., “Array sidelobes, error tolerance, gain and beamwidth,” Naval Research Lab Report, 8841, Washington DC. Sep. 28, 1984
Written By
Nali Dinesh Kumar
Submitted: 10 December 2020Reviewed: 08 April 2021Published: 05 May 2021
Open access peer-reviewed chapter
